The CCNP: your next giant hurdle in seizing Cisco certification celebration and networking know-how nirvana. I hope you have found this lab insightful.Ap| certifications | cisco - Matt McClure CCNP Labs: What is the Best Setup? In the next article, we will continue with another lab on the Cisco ASA. This brings us to the end of this Packet Tracer lab where we have configured basic settings such as hostname, domain name and interface settings on the Cisco ASA 5505. We can also check the IP settings on the ASA’s interfaces using the show interface ip brief command (as opposed to show ip interface brief on the Cisco IOS):įinally, we will ping the following devices connected to the Cisco ASA on its different interfaces: 10.0.0.100 (Inside User), 172.16.10.100 (Web Server) and 192.168.10.100 (Outside_RTR): We can begin by looking at the VLAN configuration and VLAN assignment for the interfaces using the show switch vlan command: This last sub-task is about verifying our configuration so far. Therefore, we just need to assign Ethernet0/2 to VLAN 3: interface Ethernet0/2 By default, Ethernet0/0 is already assigned to VLAN 2 (outside) and all other interfaces belong to VLAN 1. The ASA 5505 comes with switchport (L2) interfaces and the way to assign them to security zones is to assign them to the corresponding VLAN for that security zone. In our case, the task specifies that the dmz interface does not need to initiate connections to the inside, therefore our configuration will be as follows: interface Vlan3
Therefore, like the error message states, we need to use the no forward command on one of the active interfaces.
#Packet tracer labs ccnp route license
Note: An active VLAN is one configured with the nameif command.Īs such, if we try to configure VLAN 3 and add the nameif command, we will get the following message: “ ERROR: This license does not allow configuring more than 2 interfaces with nameif and without a “no forward” command on this interface or on 1 interface(s) with nameif already configured.”
#Packet tracer labs ccnp route plus
You don’t have this restriction with a Security Plus license. The third VLAN is restricted because you can only configure it to initiate traffic to only one other VLAN. With the Base License on the ASA 5505, you can only create two active VLANs and a third restricted VLAN.
This one is a bit tricky because of the license that comes with the ASA 5505 on Packet Tracer, i.e. However, IP address is enabled via DHCP so we need to change that to a static configuration. VLAN 2 also exists in the default configuration of the Cisco ASA 5505 and it has been named “outside” with a security level of 0. After removing the configuration, you can then change the IP address. One way to go about it will be to remove only the DHCP pool or to remove the entire DHCP configuration since the task doesn’t say anything about DHCP. The problem is that there is a default DHCP configuration on the ‘inside’ interface as shown below: dhcpd address 192.168.1.5-192.168.1.35 inside However, if you try to change the IP address of that VLAN interface, you will get an error message: “ Interface address is not on same subnet as DHCP pool. Therefore, the only change we need to make here is the IP address. hostname PKT-ASAīy default, VLAN 1 has already been created on the Cisco ASA 5505 and it has been named “inside” with a security level of 100. Examples include show route as opposed to show ip route and route as opposed to ip route. Actually, many of the commands that have “ip” on the Cisco IOS do not have “ip” on the Cisco ASA. Note: On the Cisco IOS, the equivalent command is ip domain-name. However unlike on the Cisco IOS, we use the domain-name command to configure a domain name on the Cisco ASA. We use the hostname command to configure the hostname on a Cisco ASA just like we do on the Cisco IOS. Verify your configuration and make sure you can ping all the connected devices from the Cisco ASA.
0 kommentar(er)
